LC TRICK BITS PAGE
Chrome rad grill.
These come with a black mesh and a chrome surround and the handle looking bits to the side. They now have slots not holls as in pic £48.
Ace bars with clock protectors
These are the old school clock protector bars. I had the same company that made them up back in the 80's make up in a small batch for me £28.

Welcome to the LC trick bits page.
I will try and add as much as I can to this page as I see things of interest, or I get things made. There is not a lot here right now, but as time goes on I will be adding to this page .

Hi flow TZ tap
These are a must for all racers and anyone who is running bigger carbs. You dont want to run weak at full thrash these will feed any carb from 26 up to 38mm powerjets £20.
The plus sets have the reed block rubbers the head to water hose bolts and the bolts for the thermostat housing.
The standard kit has all the bolts for both sides of the casings with oilpump cover, yam disk and star disk on the lc .
Complete Bike kits £35

These kits now contain the bolts for :
Brake line holds
Clutch clamp handle bar
Master cylinder
Back brake pulley arm
Fuel tap bolts
Engine mounting plates
Handle bar clamps
Exhausts bolts
Nylocks and washers for Exhausts
Bottom yoke
Top yoke
Washers Top yoke
Dome nuts Top yoke
Kickstart
Gear selector
LC grab rail
side lift handle
Caliper bolts
Alloy foot hangers
brake splitter
seat catches

Disk washers and bolts £24 a full set shown
Tab £6 set of 3, £12 with bolts

Plus Engine sets LC £15.00 a set.
Engine sets LC £8.50 a set.
Lightend flywheels They give a faster reving bike from 0 to the red line which will itself be higher by a few hundred RPM with one of these fitted. They also give less pull on the crank giving it a longer life. This is one the best mods for your money £60 each.
Stainless steel bolt kits

What they do: They can smooth out bikes that have a spluttery bit in the revs. They can help with flat spots usually found just before the powerband. They give an extra couple of BHP throughout the recv range, with pick up being sharper from the off.

How do they do it. On the up stroke a charge of attomised fuel is sent into the bottle and as soon as the other side starts to go down, even before normal fuel is sent from the carbs, the attomised fuel is sucked into the cylinder. The fuel is vaporised making it finer, so the spark burns it better and it reaches the spark sooner, making the most of the fuel going into the chamber.

BOOST BOTTLES
They are £30 each polished or £20 if you want to clean up the welds and polish yourself.
Hybrid Bottle. YPVS in LC frame or LC with YPVS reed blocks
2/350LC
V-Force Reeds These carbon fibre V-Force reeds will improve flow and increase horsepower like no other reed block mod you can do. Nothing touches them for an all round power increase. A tuned bike can get up to 6BHP with this alone. They will fit the YPVS with no mods needed. For the LC you will have to make your inlets bigger, unless you have already done this to take valve reed blocks. They are £185 a set.
Standard YPVS & V force 3

REED SPACERS
These go between the barrel and the reed block, they are cut from 6mm alloy. They allow a better flow of fuel to the transfer ports and manipulate air intake giving a better pick up and drive out of corners. By moving the cages further back slightly, it shifts power toward the bottom end for better drive. They also help reduce splutter and powerband lag that some bikes with a tune or pipes suffer from. They can also go on standard bikes. No jetting is required with them, you just fit and ride £20 a set, £4 for SS extra long bolts.

Haygon Progressive fork springs, A good mod to help fast riders and hard braking. They help stop weave and give a better feel to the front end as they are stiffer and give a better rate of dampening. A very good mode for those who like to thrash or just to give a smoother ride to anyone. £65 a set.
Progressive Forksprings

Power filters
Theys will fit any LC/YPVS & AC carb £9 each

Stearing damper
Kawasaki type Jap made and good quolity. 275mm. They have 6 setings £34

Engin Casing Joyning bolt kit £10 a set

This kit has all the top Joyning bolts and washers. It has all the washers and Nylocks for the bolts coming threw underneath as well.

Engine fitting bolts £10 a set
Theys are the bolts that fix your engine in to the frame. Ther are Stainless Steel with stainless washers and Stainless nylocks.
Chrome tuning fork decal for clear clutch covers £5
Stearing damper Fitting Kit The fork bracket is alloy and Anodized silver.
The side bracket is Stainles steel.
£25a kit or £30 with ST/ST beacket in mirror polished finish.
Stanless steel Top yoke bolt " Standard looking type"
They are £15 each
Both are mirror polished HI Grade ST/ST
Center stand spring
Theys are made in stainles steel and look the biz on your bike. £8
Side stand spring
Theys are made from stainless steel and look well trick when polished. £7.50

ST/ST Banjo bolts & washers
single £ 4.25
Doubble £5.00
Washers 50p each

Center stand C Piece
Theys are made in stainles steel £4 as seen in satin finish, £6 with mirror polish.

Engine fitting brackets
Theys engine fixing brackets go with the above bolts and fix the bike in the frame.They are made from top quolity Stainless steel

£12 a set with a Satin Finish (unpolished)

They can be polisged up realnice with a bit of time.

Back Brake spring
Theys are made from stainless steel. They fit as shown from brake pedel to hanger £5
Stanless steel Top yoke bolt "Tuning fork type"
They are £20 each
Click the picture for a link to a better view

Digital Programable Ignitions
They are designed to work with your original stator and fly wheel. They are an excelent upgrade for a race bike and feel out of this world on a road bike. programer £55 Ignition Box £95 Unrestricted CDI £70

All in 1 unit £150 bar switch so you can swop curvs on the mover £15

You can store 10 custom curves
Presat with some populer curves to mod or swop
Easy and fast programing at track side
You have 4 to 10 curve points
Instant monitoring of rev's via LCD hand held
Timing calculations for every 1 RPM change
They come with full instructions and speck sheets.

Yoke Spacers for RGV
If you are doing a RGV yoke convershon you will need 1 of theys for the bottom yoke so the taper head bearings will fit. £5 each
Tapper head bearings are £35
Brake plate bars
Theys are made from 6mm thick alloy and are as seen.
wiggle or strate Slotted £20 Polished £27
Plain £15 Polished£22

Head bolts
Stainles steel With a dished head for that more standard look but nicer with a dished head (unpolished shown)

£60 a set
£65 polished

Head bolts
Stainles steel with the tuning forks on top. For that Ultra Trick look.
They come with the 8 stainles washers as seen (unpolished shown)

£70 a set
£75 a set mirror polished

All Stainless Bolts are made from top quolity stainles.
Carbon fibre engine disks
As seen the yam disk and the star disk for an LC. The yam will ofcourse fit a YPVS as well.
£25 each

Wavey disks
Theys are the only wavey disks availabe for theLC becourse I Designed them.
They have Lightweight alloy centers and are full floating disks as you can see and this makes them a lot lighter then standard disks .

You can run standard calipers they are the same size as original disks, no extra hangers are needed for theys disks just replace your sad round ones and ride away with theys trick disks.

I made them 1mm thicker then standard to add more to there life. They are made from a special carbon steel that gives a lot better braking then standard disk Material. They have been PDQ hardened, this is what gives them the black look. Unfortunately this is only a by product of the hardening and will come of as soon as you start braking then they turn silver as normal. They are £260 a pair

Casrbon fibre Twin horn cover
Theys are solid carbon with alloy mesh at the back and ST/ST dome head bolts £13.50

Braded steel brake lines

They are made from Hard drawn tensile Stainless steel braded teflon hose . The ends and fasteners are all Stainless steel.

They come as a kit as you se with bolts and washers att ST/ST as well ofcourse.
single line 250LC £24
Tripple line 350lc £72

Braded steel brake lines

They can be made to order in all the colours you see.

Stock lines are with clear cover and with a light tint cover. Theys are the very best you fined .

A real special bit of bolt on bling Carbon fibre Rad plates. They are £30 a set of 2. Designed to go with a chrome rad grill as shown.
Speedo Trip Knobs
Theys made from alloy and anodysed black with the tuning forks engraved in the ends. £14 each
plane dished head (stabdard looking) £13
Silicone Hose Sets
They come in a Dark Blue / Red and Black. The standard 3 hose set is £36 if you want the extra rad to header hose add £7. They are 3 core Hose's with a smooth bore for a faster water flow. They are a little longer so you have room to play with and trim up to soot. They will not rot or bulge over time, so why not add a bit of sparkle to your bike.
Alloy rear sets
Theys are a quolity Torozzi reaeset they have spring loaded ball pegs so they snap up and down and stay there located by the ball and come with rubber pegs or alloy nurled pegs as shown. £169 a set
Center stand pin
Theys are made from a high grade stainles steel £15
side stand bolt
Stainless steel engraved with the tuning forks £10
Tuning for fork bolts
Theys are made in alloy and are anodysed black they have an o ring grovedin with an O ring to hiold them in place. I big inprovement over the standed plastic cap £30 a pair

Phome Power filters
Thys are a duel density filter and come with clip as shown. £10 each

Chrome rad grill Spacers.
These are made from alloy and fit around the chrome part so space them out from the rad . Without theys they sit on the rad toutching. £12 a set
Out Of stock
Out Of stock
Rad plates sold out